Why is Rock River flood water treated as contaminated?
River water is not clean water. It has traveled over farmland, roads and storm drains and through whatever the system outside carried, so it is handled as contaminated regardless of how clear it looks. That decides which materials are removed and what cleaning is done before drying starts.
Restoration work sorts water by what is in it rather than by how much there is. A supply line that bursts inside a wall starts out clean. Water that has crossed ground outside and entered a building has not, and that is true of a clear-looking crest as much as of an obviously muddy one. The practical result is that porous materials which would be dried and kept after a clean-water loss are removed after a river flood.
This is also why the sequence matters. If drying equipment is run before the silt and surface contamination are cleaned off, the air movers distribute what was lying on the slab. Cleaning first, then drying, is slower on day one and much faster over the week, and it is the difference between a lower level that smells right afterwards and one that does not.
What do the river gauge numbers actually mean for my house?
The National Weather Service ties stages at Afton to real places. At 11.1 feet, flood water reaches Riverside Park and a road inside it on the north side of Janesville. The 2008 record was 13.51 feet, and April 2026 crested at about 12.11 feet, a provisional reading.
Gauge readings are useful because they repeat. A stage that put water in a particular low spot once will tend to do it again, and the Weather Service publishes those impact statements for exactly that reason. The major flood level at Afton is given as 12.2 feet, which is why the April 2026 crest was watched so closely as it approached it.
What the gauge cannot tell you is how water will reach your particular building. A reading describes the river, not your lot, your grading or your foundation. A house a street back from the water can take seepage while a neighbor closer in stays dry, because the path is through soil rather than over the bank. The gauge tells you when to pay attention; the first visit tells you what is happening to your building.
- Note the date and time water first appeared, and the depth at its highest
- Photograph the silt line before anything is cleaned or moved
- Keep receipts for pumps, fans or dehumidifiers you bought or hired yourself
- Write down which rooms lost power and when
What moves the price of a river flood job up or down here?
Depth and floor area come first, then how contaminated the water was, how much porous material has to come out, how hard the lower level is to reach with equipment, and how long the water sat. The scope is explained and approved before any work starts, and no figure is quoted without a visit.
The biggest single factor is how much of the building the water touched, and that is not the same as how deep it was. Two feet across a finished lower level with carpet, drywall and built-in cabinets is a far larger job than two feet in an open block-walled basement with a painted slab. Contaminated water adds the cleaning step and the removal of porous materials, which both take labor.
Access changes the number too. A walk-out or an overhead door lets a crew move pumps, hoses and debris directly; a narrow interior stair means every piece of equipment and every bag of wet material is carried. How long the water stood matters because wet material that has been saturated for days has usually lost the chance to be dried in place. Rebuild work, which means new drywall, flooring and paint, is quoted separately by the contractor who does it.
Does a homeowners policy cover river flooding?
Generally no. In WI, flood damage needs separate flood cover, and foundation seepage is not covered under a standard homeowners policy. Sewer or sump backup usually needs an endorsement. The Wisconsin Office of the Commissioner of Insurance publishes consumer information on these distinctions, and your own policy and insurer decide any outcome.
The distinction that surprises people is that the cause matters more than the water. Surface water that rises and enters a building is flood, and flood is its own line of cover. Water that comes back up a drain is backup, which is a separate endorsement again. Water that weeps through a foundation wall is seepage, which a standard policy does not pick up.
None of that changes what the building needs, and it does not change the order of work. Photograph the damage, tell your insurer promptly, and do not throw property away before the adjuster has approved it. Those three habits protect a claim whichever line of cover turns out to apply, and the crew's dated photographs and moisture log support them.
How long does drying take after river water?
Pumping is usually a matter of hours. Drying runs for days, and the length depends on how wet the framing and masonry got rather than on the calendar. Equipment comes out when readings at marked points reach target, which is normally several visits after the floor looks dry.
A slab and a block wall hold a surprising amount of water, and they release it slowly into the air around them. That is what the dehumidifiers are for. A finished lower level with insulation in the stud bays takes longer than an open basement, because the wet material is behind a surface that has to be opened before air can reach it.
The honest answer for any one building comes from the readings. If the moisture content of the bottom plate is still high on the fourth visit, the equipment stays. Pulling fans early is the most common way a flood job turns into a mold job three weeks later, and it is the reason the log exists.